Lost Vape Ultra Boost Pro Coils | Pack of 3
Replacement coils for the Lost Vape UB Pro pod tank. Two options in the Pro series — the P1 at 0.15Ω and the P3 at 0.3Ω. Both mesh. Both high-wattage DTL. Press-fit installation, no threading. If you're running the Ursa Quest or a compatible UB Pro pod system, these are the ones you need.
The Two Coils in a Pack of 3 Size
UB Pro P1 — 0.15Ω Mesh — 70–90W
The higher-output coil. Wide open DTL draw, maximum vapour production. Kanthal mesh, wattage mode only. At 70–80W the flavour is dense and warm — the kind of draw that suits high-VG liquid at 3mg where you want cloud and saturation rather than nicotine hit. Ramps up fast, performs consistently through the life of the coil. Best paired with 70/30 VG/PG or higher.
UB Pro P3 — 0.3Ω Mesh — 60–75W (also SS904L temp control)
The more versatile of the two. Still DTL, still high wattage, but the resistance gives a slightly cooler, more controlled draw than the P1. Constructed from SS904L stainless steel wire — runs in standard wattage mode like any coil, but also supports temp control on devices with SS TC mode. In TC it sits between 260–290°C (500–550°F). A good choice if you want a bit more control over the draw character or if your mod has TC and you want to use it. High-VG liquid at 3–6mg works well.
Product Specifications
| Specification | Detail |
| Coil Series | UB Pro (Ultra Boost Pro) |
| P1 Resistance | 0.15Ω |
| P1 Wattage | 70–90W |
| P1 Material | Kanthal Mesh |
| P1 Style | DTL |
| P3 Resistance | 0.3Ω |
| P3 Wattage | 60–75W |
| P3 Temperature (TC) | 260–290°C / 500–550°F |
| P3 Material | SS904L Mesh |
| P3 Style | DTL (Wattage & TC modes) |
| Installation | Press-Fit |
| Pack Size | 3 Coils |
| Compatible Devices | Lost Vape Ursa Quest, UB Pro Pod Tank |
Compatible Devices
The UB Pro coil series is specific to the UB Pro pod tank used in:
Lost Vape Ursa Quest Pod System
Lost Vape Ursa Quest Multi
These are not interchangeable with the standard Ultra Boost (UB Ultra/V2) coil series used in the Thelema, Gemini, BTB, or Orion Q-Ultra — different fitting, different series. Check your device before ordering.
Priming
Press-fit the coil into the base of the pod. Fill the pod with E-Liquid, replace the cap, and wait at least five minutes before the first draw. At 70–90W the coil gets hot fast — dry cotton at those wattages burns immediately and there's no recovering a scorched UB Pro coil. Prime it, wait it out, start at the lower end of the wattage range for the first few draws before settling in.
E-Liquid
High-VG for both coils. The mesh wicking ports on the P1 and P3 are built for 70/30 VG/PG and above. At the wattages these coils run, thin 50/50 liquid gets through fine but the vapour production and warmth really come from thicker liquid. Freebase e-liquid at 3mg or 6mg is standard — nic salts at this wattage level are generally too harsh for most vapers.
What's in the Box
3 x Lost Vape Ultra Boost Pro Coils (P1 or P3 — same resistance per pack)
Price
Available at VapeOnlineStore.co.uk. Fast UK delivery. Pick up both the P1 and P3 at the same time if you haven't tried both — the draw difference between 0.15Ω and 0.3Ω at high wattage is noticeable enough to have a preference.
Get exclusive deals and early access to offers by subscribing to the Vape Online Store newsletter.
Frequently Asked Questions
What devices are the Lost Vape Ultra Boost Pro coils compatible with?
The UB Pro coil series fits the Lost Vape Ursa Quest pod system via the UB Pro pod tank. They are not compatible with the standard UB Ultra/V2 coil series devices such as the Thelema, Gemini, or Orion Q-Ultra — those use a different fitting.
What is the difference between the Lost Vape Ultra Boost Pro P1 and P3 coils?
The P1 is 0.15Ω Kanthal mesh, rated 70–90W, wattage mode only. The P3 is 0.3Ω SS904L mesh, rated 60–75W, and supports both wattage mode and temp control (260–290°C). The P3 gives a slightly cooler, more controlled DTL draw. The P1 is higher output and warmer.
Can I use the UB Pro P3 coil in temp control mode?
Yes. The P3 is built from SS904L stainless steel wire, which is compatible with SS temp control on devices that support it. Run it between 260–290°C / 500–550°F. In wattage mode, use it at 60–75W.
What e-liquid should I use with the Lost Vape Ultra Boost Pro coils?
High-VG liquid — 70/30 VG/PG or higher. Freebase e-liquid at 3–6mg suits the wattage range. Nic salts at these output levels are generally too harsh for most vapers.
How do I install the Lost Vape Ultra Boost Pro coils?
Press-fit. Push the coil into the base of the UB Pro pod until it clicks into position. No threading needed. Fill the pod, wait five minutes to prime, then start at the lower end of the recommended wattage before increasing.
How long do the Lost Vape Ultra Boost Pro coils last?
With high-VG liquid and proper priming, expect one to two weeks from each coil under regular daily use. Running the device consistently at the top of the wattage range or using thinner liquid shortens coil life. Start lower and build up for best longevity.
Original: $12.06
-70%$12.06
$3.62Product Information
Product Information
Shipping & Returns
Shipping & Returns
Description
Replacement coils for the Lost Vape UB Pro pod tank. Two options in the Pro series — the P1 at 0.15Ω and the P3 at 0.3Ω. Both mesh. Both high-wattage DTL. Press-fit installation, no threading. If you're running the Ursa Quest or a compatible UB Pro pod system, these are the ones you need.
The Two Coils in a Pack of 3 Size
UB Pro P1 — 0.15Ω Mesh — 70–90W
The higher-output coil. Wide open DTL draw, maximum vapour production. Kanthal mesh, wattage mode only. At 70–80W the flavour is dense and warm — the kind of draw that suits high-VG liquid at 3mg where you want cloud and saturation rather than nicotine hit. Ramps up fast, performs consistently through the life of the coil. Best paired with 70/30 VG/PG or higher.
UB Pro P3 — 0.3Ω Mesh — 60–75W (also SS904L temp control)
The more versatile of the two. Still DTL, still high wattage, but the resistance gives a slightly cooler, more controlled draw than the P1. Constructed from SS904L stainless steel wire — runs in standard wattage mode like any coil, but also supports temp control on devices with SS TC mode. In TC it sits between 260–290°C (500–550°F). A good choice if you want a bit more control over the draw character or if your mod has TC and you want to use it. High-VG liquid at 3–6mg works well.
Product Specifications
| Specification | Detail |
| Coil Series | UB Pro (Ultra Boost Pro) |
| P1 Resistance | 0.15Ω |
| P1 Wattage | 70–90W |
| P1 Material | Kanthal Mesh |
| P1 Style | DTL |
| P3 Resistance | 0.3Ω |
| P3 Wattage | 60–75W |
| P3 Temperature (TC) | 260–290°C / 500–550°F |
| P3 Material | SS904L Mesh |
| P3 Style | DTL (Wattage & TC modes) |
| Installation | Press-Fit |
| Pack Size | 3 Coils |
| Compatible Devices | Lost Vape Ursa Quest, UB Pro Pod Tank |
Compatible Devices
The UB Pro coil series is specific to the UB Pro pod tank used in:
Lost Vape Ursa Quest Pod System
Lost Vape Ursa Quest Multi
These are not interchangeable with the standard Ultra Boost (UB Ultra/V2) coil series used in the Thelema, Gemini, BTB, or Orion Q-Ultra — different fitting, different series. Check your device before ordering.
Priming
Press-fit the coil into the base of the pod. Fill the pod with E-Liquid, replace the cap, and wait at least five minutes before the first draw. At 70–90W the coil gets hot fast — dry cotton at those wattages burns immediately and there's no recovering a scorched UB Pro coil. Prime it, wait it out, start at the lower end of the wattage range for the first few draws before settling in.
E-Liquid
High-VG for both coils. The mesh wicking ports on the P1 and P3 are built for 70/30 VG/PG and above. At the wattages these coils run, thin 50/50 liquid gets through fine but the vapour production and warmth really come from thicker liquid. Freebase e-liquid at 3mg or 6mg is standard — nic salts at this wattage level are generally too harsh for most vapers.
What's in the Box
3 x Lost Vape Ultra Boost Pro Coils (P1 or P3 — same resistance per pack)
Price
Available at VapeOnlineStore.co.uk. Fast UK delivery. Pick up both the P1 and P3 at the same time if you haven't tried both — the draw difference between 0.15Ω and 0.3Ω at high wattage is noticeable enough to have a preference.
Get exclusive deals and early access to offers by subscribing to the Vape Online Store newsletter.
Frequently Asked Questions
What devices are the Lost Vape Ultra Boost Pro coils compatible with?
The UB Pro coil series fits the Lost Vape Ursa Quest pod system via the UB Pro pod tank. They are not compatible with the standard UB Ultra/V2 coil series devices such as the Thelema, Gemini, or Orion Q-Ultra — those use a different fitting.
What is the difference between the Lost Vape Ultra Boost Pro P1 and P3 coils?
The P1 is 0.15Ω Kanthal mesh, rated 70–90W, wattage mode only. The P3 is 0.3Ω SS904L mesh, rated 60–75W, and supports both wattage mode and temp control (260–290°C). The P3 gives a slightly cooler, more controlled DTL draw. The P1 is higher output and warmer.
Can I use the UB Pro P3 coil in temp control mode?
Yes. The P3 is built from SS904L stainless steel wire, which is compatible with SS temp control on devices that support it. Run it between 260–290°C / 500–550°F. In wattage mode, use it at 60–75W.
What e-liquid should I use with the Lost Vape Ultra Boost Pro coils?
High-VG liquid — 70/30 VG/PG or higher. Freebase e-liquid at 3–6mg suits the wattage range. Nic salts at these output levels are generally too harsh for most vapers.
How do I install the Lost Vape Ultra Boost Pro coils?
Press-fit. Push the coil into the base of the UB Pro pod until it clicks into position. No threading needed. Fill the pod, wait five minutes to prime, then start at the lower end of the recommended wattage before increasing.
How long do the Lost Vape Ultra Boost Pro coils last?
With high-VG liquid and proper priming, expect one to two weeks from each coil under regular daily use. Running the device consistently at the top of the wattage range or using thinner liquid shortens coil life. Start lower and build up for best longevity.